GMPM16-30Z SMC MGPM/L series Compact guide cylinder Slide bearing

1: Product Name: GMPM16-30Z SMC MGPM/L series Compact guide cylinder Slide bearing


2: Order Code

3: Standard Stroke

Bore size (mm)	Standard stroke (mm)
12, 16	10, 20, 30, 40, 50, 75, 100, 125, 150, 175, 200, 250
20, 25	20, 30, 40, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400
32 to 100	25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400

4: Specification

Action	Double acting
Fluid	Air
Proof pressure	1.5MPa
Max. operating pressure	1.0MPa
Min. operating pressure	ø12, ø16	0.12MPa
	ø20 to ø100	0.1MPa
Ambient and fluid temperature	–10 to 60° C (with no freezing)
Piston speed	ø12 to ø63	50 to 500mm/s
	ø80, ø100	50 to 400mm/s
Cushion	Rubber bumper at both ends
Lubrication	Non-lube
Stroke length tolerance	0~+1.5mm

5: Manufacture of Intermediate Strokes

Part number	Refer to standard part numbers and ordering procedure.		Indicate -XB10 at the end of the standard model no. Refer to P.52 for order made specifications.
Applicable stroke (mm)	ø12, ø16	1 to 249	ø12, ø16	11 to 249
	ø20, ø25, ø32	1 to 399	ø20, ø25	21 to 399
	ø40 to ø100	5 to 395	ø32 to ø100	26 to 399
Example	Part no.: MGPM20—39 A spacer 1mm in width is installed in a MGPM20—40. C dimension is 77mm.		Part no.: MGPM20—39—XB10 Special body manufactured for 39mm stroke. C dimension is 76mm.

6: Installation
1.When load changes in the work, the cylinder with abundant output capacity shall be ed.
2.The medium used by cylinder shall be filtered to 40μm or below.
3.Dirty substances in the pipe must be cleared away before cylinder is connected with pipeline to prevent the entrance of particles into the cylinder.
4.Necessary protection measure shall be taken in the environment with higher humidity, much dust or water drops, oil dust and welding dregs.
5.The cylinder shall avoid the influence of side load in operation to maintain the normal work of cylinder and extend the service life.
6.Relative cylinder with high temperature resistance or corrosion resistance shall be chosen under the condition of high temperature or corrosion.
7.Anti-freezing measure shall be adopted under low temperature environment to prevent moisture freezing.
8.If the cylinder is dismantled and stored for a long time, please conduct anti-rust treatment to the surface. Anti-dust cap shall be ed into the inlet and outlet ports. As the precision of the manufacture and  guide is high, never dismantle the fixed block or cylinder cover without permission.
7: Constructure and Material


8: Structure and Dimension
1. ø12 to ø25/MGPM, MGPL


2. ø32 to ø63/MGPM, MGPL



3. ø80, ø100/MGPM, MGPL


9: Products Shopping Guide
For example: you want to purchase a batch of cylinders but you don't know which type you are really want, so you can tell me all your requirement and I'll recommend to you.
10: Delivery
1. If the products we have in store, we will send it out ASAP after payment.
2. We have a variety of ways to send goods, usually DHL, Fedex, TNL will be normal ways. If you require use of a courier, we can do it.
3. Also we can send by your delivery acount if you want.
4. If the products which were customized, we will complete the production within a specified period of time, and send it out the first time, we can promise it.
11: After-sale Service
We can provide a series of after-sale service, such as product introduction, mounting, debugging, technical support and so on.