1: Product Name: SMC CQ2 series Compact cylinder CQ2YB25-100 Standard double acting 2: Order Code
3: Specification Bore(mm) | 12 | 16 | 20 | 25 | 32 | 40 | 50 | 63 | 80 | 100 |
Fluid | Air |
Action | Double acting, single rod |
Proof pressure | 1.5MPa |
Maximum operating pressure | 1.0 Mpa |
Minimum operating pressure | | | | | | | | | | |
Ambient and fluid temperature | Without auto switch: –10 to 70°C (No freezing) With auto switch: –10 to 60°C (No freezing) |
Lubrication | Lubrication |
Piston speed | 50 to 500 mm/s |
Allowable kinetic energy (J) | 0.02 | 0.04 | 0.06 | 0.09 | 0.15 | 0.26 | 0.46 | 0.77 | 1.36 | 2.27 |
Stroke length tolerance | +1.0 mm Note) |
0 |
4: Stroke Standard Bore Size | Standard Stroke |
20, 25 | 5, 10, 15, 20, 25, 30, 35, 40, 45, 50 |
32, 40 | 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 75, 100 |
50, 63, 80, 100 | 10, 15, 20, 25, 30, 35, 40, 45, 50, 75, 100 |
5: Weight Bore size (mm) | |
5 | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 | 50 | 75 | 100 |
12 | 29 | 35 | 41 | 47 | 54 | 60 | - | - | - | - | - | - |
16 | 42 | 50 | 59 | 67 | 76 | 84 | - | - | - | - | - | - |
20 | 63 | 75 | 88 | 101 | 114 | 127 | 140 | 152 | 165 | 178 | - | - |
25 | 86 | 100 | 115 | 129 | 144 | 158 | 173 | 187 | 202 | 216 | - | - |
32 | 125 | 145 | 165 | 184 | 204 | 224 | 244 | 263 | 283 | 303 | 448 | 547 |
40 | 187 | 208 | 230 | 251 | 273 | 294 | 315 | 337 | 358 | 380 | 552 | 664 |
50 | - | 339 | 372 | 405 | 438 | 471 | 504 | 537 | 570 | 603 | 872 | 1043 |
63 | - | 480 | 518 | 556 | 594 | 632 | 670 | 708 | 746 | 784 | 1112 | 1308 |
80 | - | 916 | 976 | 1036 | 1097 | 1157 | 1217 | 1277 | 1338 | 1398 | 1917 | 2215 |
100 | - | 1608 | 1688 | 1768 | 1849 | 1929 | 2010 | 2090 | 2170 | 2251 | 2982 | 3391 |
6: Installation Caution 1. Connection with a work piece
When a work piece is mounted on the piston rod end, connect them aligning the center of piston rod and a work piece. If they are offcenter, lateral load is generated and phenomena mentioned in (1) may occur. In order not to apply the off-center load, use of a floating joint or simple joint is recommended.
2. Simultaneous use of multiple cylinders
It is difficult to control the speed of pneumatic cylinders. The following conditions cause speed change: change in supply pressure, load, temperature and lubrication, performance difference of each cylinder, deterioration of each part over time, etc. A speed controller can be used to control the speed of multiple cylinders simultaneously for a short period of time, but depending on conditions, it may not work as desired. If multiple cylinders cannot operate simultaneously, unreasonable force is applied to the piston rod because cylinder positions may not be the same. This may cause abnormal friction of seals and bearings, and galling of cylinder tubes and pistons. Do not use an application to operate several cylinders simultaneously by adjusting cylinder speed. If this is inevitable, use a high rigid guide against load, so that the cylinder is not damaged even when the each cylinder output is slightly different.
3. Allowable lateral load
Lateral load that can apply to the piston rod end is limited. If a cylinder is used with
a lateral load over the limit, it may cause air leakage due to abnormal friction of seals, galling of cylinder tubes and pistons, or abnormal friction of the bearing part. The lateral load applied to the piston rod must be within the allowable range indicated in this catalog. When the load exceeds the limit, use a double rod cylinder, install a guide, or change the bore size to suit the load in order to make the load within the allowable range. As a standard product, an anti-lateral load type cylinder that is resistant to approx. 2 times more than the conventional compact CQ2 series is also available (page 128).
7: Delivery 1. If the products we have in store, we will send it out ASAP after payment.
2. Also we can send by your delivery acount if you want.
3. If the products which were customized, we will complete the production within a specified period of time, and send it out the first time, we can promise it.
4. We have a variety of ways to send goods, usually DHL, Fedex, TNL will be normal ways. If you require use of a courier, we can do it.
8: Competitive Advantage Our product features | Our Services Guarantee: |
1) Competitive price | 1) Prompt respond (Reply with 24 hours) |
2) Good quality | 2) Free Samples (Customer pay for the delivery cost) |
3) Professional Packaging | 3) Registration support. |
4) Produce according to Customers’ instruction | 4) Photos/videos are available during production. |
5) None delay shipment | 5) Loading inspection, and send loading photos before shipment. |
9: After-sale service We can provide a series of after-sale service, such as product introduction, mounting, debugging, technical support and so on.